Page Connection Panel Rear Note: Be sure to only use wireless transmitters that comply with local radio regulations. You must turn off the power before con- necting or disconnecting the power cord or AC adaptor. Page 15 Note: Do not forget to connect the module, synthesizer, etc. See its manual for details.
Page Powering Up a few seconds after power up is required before it will operate normally. Note: If the AX-Synth is connected to a keyboard amp or audio amp, turn on the power of the AX-Synth first, and then switch on your amp. These sounds can be played via the 49 velocity-sensitive keys or via MIDI. The factory default, Hz, represents the reference pitch used by most electronic musical instruments. You only need to do this once: the AX-Synth will remember this setting until you change it again.
Note: The knob does not return to its minimum setting auto- matically. In such cases, we recommend using the [HOLD] button. For example, one device can play or switch sounds on the other device.
In such a case, please repeat the entire procedure. Page Additional Functions All indicators flash. Not all MIDI instruments support all Control Changes, while some instruments may use certain numbers for different pur- poses. Be sure to check the MIDI implementation chart of the external instrument.
Page 42 Information When you need repair service, call your nearest Roland Service Center or authorized Roland distributor in your country as shown below. Print page 1 Print document 44 pages. Rename the bookmark. Delete bookmark? Also, all cords and cables should be placed so they are out of the reach of children. In the interest of safety, please read and observe the following precautions. In addition, avoid mixing different types of batteries.
Then install new batteries. To avoid inflammation of the skin, make sure that none of the battery discharge gets onto your hands or skin.
Exercise the utmost caution so that none of the discharge gets near your eyes. Immediately rinse the affected area with running water if any of the discharge has entered the eyes. Be careful to insert the batteries the right way around. Depending on the way in which the electrical appliance is used, power supply noise may cause this unit to malfunction or may produce audible noise. If it is not practical to use a separate electrical outlet, connect a power supply noise filter between this unit and the electrical outlet.
This is normal, and is not a cause for concern. To alleviate the problem, change the orientation of this unit; or move it farther away from the source of interference.
Do not use this device in the vicinity of such receivers. Such noise could occur when receiving or initiating a call, or while conversing. Should you experience such problems, you should relocate such wireless devices so they are at a greater distance from this unit, or switch them off.
Excessive heat can deform or discolor the instrument. Damage or malfunction may result if you attempt to use the AX-Synth in this condition. Therefore, before using the AX-Synth, you must allow it to stand for several hours, until the condensation has completely evaporated.
This can be the cause of malfunction, such as keys ceasing to produce sound. You can place a piece of felt or cloth under the rubber feet to prevent this from happening. If you do so, please make sure that the unit will not slip or move accidentally. To remove stubborn dirt, use a mild, non-abrasive detergent. Afterwards, be sure to wipe the instrument thoroughly with a soft, dry cloth. Important data should always be backed up using the Bulk Dump function see p.
In certain cases such as when circuitry related to memory itself is out of order , we regret that it may not be possible to restore the data. Roland assumes no liability concerning such loss of data. To protect yourself against the risk of losing important data, we recommend that you periodically save a backup copy of important data you have stored in the unit's memory see p. Roland Europe assumes no liability concerning such loss of data.
Rough handling can lead to malfunctions. You may prefer to use headphones, so you do not need to be concerned about those around you especially when it is late at night. Otherwise, you will need to use equivalent packaging materials. Please be aware of this when using the D Beam controller outside.
Keep your discs clean using a commercially available CD cleaner. Please see the documentation that came with the batteries. This may cause heat generation and formation of rust on the battery and its terminals. Take them back to your dealer.
Never heat it. Doing so may melt the insulation, damage the gas release vents or protective devices, cause combustion through chemical reaction with generated hydrogen, ejection of battery fluid, bursting or fire.
Strong impact can cause leakage of battery fluid, heat generation, bursting or fire. Never disassemble the batteries. Strong alkaline fluid can damage the eyes and lead to permanent loss of eyesight. Battery fluid can cause skin damage. Before use, you must read and strictly observe all of the precautions that accompany the batteries, rechargeable batteries, or battery charger. When using rechargeable batteries and a charger, use only the combination of rechargeable batteries and charger specified by the battery manufacturer.
The AX-Synth in a nutshell. Panel descriptions. Front panel. Connection panel rear. Making connections. Connecting the AC adaptor.
Playing the AX-Synth. Master Tune. Editing Tone settings. Editing the volume and Reverb Send levels. General considerations. Additional functions. Battery-related functions. MIDI implementation chart. If combined with a commercially available wireless system, it allows you to play wherever you like, to follow the singer or any other musician on stage, etc.
It even provides an attenuator switch to adapt its output level to the input sensitivity of the wireless system you are using. Dedicated editor and librarian software is also available. The AX-Synth provides control functions that are conveniently and ergonomically built into its neck. The D Beam controller can be set to transmit almost any control change message CC you may ever need. The AX-Synth comes with dedicated editor and librarian software that allows you to modify and save all aspects of the internal sounds.
Combined with this intuitive software, the AX-Synth becomes a fully-fledged synthesizer. These buttons are used to transmit program change messages on the selected MIDI channel. They work in a sequential fashion incremental or decremental. Program change numbers can also be entered directly, however see p.
Pressing this button allows you to select the secondary hidden function of some of the other buttons. This three-character display keeps you posted about the selected Tone, mode or the parameter value you set. These buttons allow you to select a Tone from the active Tone family see above in a sequential fashion. This knob sends channel aftertouch messages for the notes you are playing see p. The buttons to its left allow you to assign the desired function to the D Beam controller see p.
Press the modulation bar to add modulation to the notes you are playing. Behind the modulation bar lies the ribbon strip. Slide your finger towards the left or right on this ribbon to change the pitch of the notes. This is where you can attach the ends of the supplied strap. Choose any two pins. To take advantage of the AX-Synth mobility factor, consider using a commercially available wireless system.
For optimum sound quality, we recommend working in stereo, though. Note: Be sure to only use wireless transmitters that comply with local radio regulations. This is a safeguard against accidental disconnection. Note: Though you can also connect an expression pedal, any pedal you connect will act as Hold pedal. If you connect the supplied adaptor to the DC IN socket, be sure to wind its cable around this hook as a safeguard against accidental disconnection.
If this happens, use connection cables that do not contain resistors. Note: Be sure to use only the supplied AC adaptor. Using any other type may cause malfunction or electric shock. Note: If the AX-Synth is to remain unused for an extended period of time, unplug the adaptor. Place the AC adaptor so the side with the indicator see illustration faces upwards and the side with textual information faces downwards.
Note: Depending on your region, the included power cord may differ from the one shown above.
0コメント