Quick Links. Tri-Tronics Owner's Guide. Table of Contents. Previous Page. Next Page. Page 2: Product Specifications Product specifications may change without notice or obligation since Tri-Tronics is committed to a policy of continuous improvement. Certain Tri-Tronics products are covered by one or more of these U. Page 5: Quick Guide Select an intensity level for training: Level 1 is the lowest; level 6 is the highest level 5 is the highest on the Classic Release the transmitter button when c h a n g i n g levels during training.
Intensity selection tips are in the training manual and video that came with your Remote Trainer. Page Setting The Intensity Level 3: Medium intensity Level 4: Medium-high intensity Level 5: High intensity Level 6: Very high intensity not available on the Classic 70 When increasing or decreasing intensity using the intensity knob, be sure you have released the stimulation buttons, or your new intensity selection will not take effect.
Page Using The Stimulation Buttons To produce a series of momentary corrections, press the button for each correction. This feature allows the trainer to choose instantly among low, medium, and high stimulation. This selection feature applies to either continuous or momentary stimulation, or to both, depending on the model. Please call our Customer Service Department at with any questions. Page 26 Moisture and debris fitted properly can enter charging jack. Use only the correct Tri-Tronics chargers to charge your Remote Trainer.
Using the wrong type of charger may damage batteries or the unit itself. Do not charge batteries that are not installed in a Remote Trainer.
Page 27 When your batteries do need to be replaced, you can replace them yourself with parts obtained from Tri-Tronics. Carefully read the instructions. If you have any questions concerning it, or if you suspect that your Remote Trainer is malfunctioning, please call our Customer Service Department at Page Product Safety Tri-Tronics Remote Trainers have two independent circuits that are designed to inhibit excessive electrical stimulation.
One is located in the transmitter, the other is in the collar. Charging Contacts Place the transmitter in the supplied cradle to charge.
Page 7 Intensity Dial Intensity levels: 1, 2, 3, 4, 5, 6 Line up the number you select with the round light. Page 8 The receiver is waterproof. This light will be: Green when the batteries are full. Amber when the batteries are partly discharged. Red when the batteries need charging very soon. Rapid red flashing means the batteries are completely dead and the unit will not function. Check contact points regularly for tightness. Use only our plastic wrench to remove or tighten and do not over tighten.
When adding a straps is available from Tri-Tronics or your favorite dealer. Page 13 Use only the wall cube supplied by The new cradle charging system keeps your receiver batteries in better condition Tri-Tronics with the charging cradle.
The charger charges rapidly — only two hours are needed. Page Fitting The Collar On The Dog This flexible approach to remote training has made Tighten the buckle by holding it with two fingers as Tri-Tronics products the favorite of both experienced trainers and beginners for you pull the strap snug. Remote training collars many years. Future accessories will also The Tri-Tronics Beeper lets you know where your bird dog is hunting and when be operated with this setting.
The Beeper has a wide choice of settings to suit different hunting styles and individual preferences. Page 17 Battery. One 9-volt battery is already installed. The Beeper power must be on for the Beeper to operate. Press the round power switch located on the rear surface of the Beeper.
You will hear two tones and the Beeper light will begin flashing. Page 18 Run Tones. Be sure that the Tri-Tronics logo on the battery pack is facing forward under the transmitter Your product is shipped with one 9-volt battery installed. Please contact our Customer Service Department at support tritronics. Page 21 If using a power strip, make sure it is switched on and working. You are using the wrong transmitter. Page 22 Problem 4: The receiver light changes color to indicate low charge Problem 8: The cradle light blinks red slowly when the unit is very quickly.
The unit has been left turned on between training sessions. Make sure the The cradle has diagnosed a failure condition in the battery pack being receiver is turned off after use.
Page Basic Training Introduction However, the use of an e-collar is not a short cut.
0コメント